• Free shipping to the continental U.S.
  • Third-party tested sound deadening
  • Pre-cut kits for your vehicle
(877) 211-5597
Semi Truck Sound Deadening

Sound Deadening for Semi Trucks and Sleeper Cabs

Sound deadening helps a semi cab most where road, tire, and engine noise enter the cab: the floor, the firewall, the doors, and the sleeper walls. Less of that noise makes long hauls easier and rest in the bunk more restful.

This guide explains where semi cab noise comes from, which zones to treat first in a sleeper, which materials do which job, and which SoundSkins kits fit trucks today.

Where semi cab and sleeper noise comes from

Five paths carry most of the noise into a semi cab. Each one calls for a different fix.

  • Road and tire. Tire noise enters through the wheel wells and the floor pan. A ladder frame carries more of that energy into the cab than a car body does, according to Dynamat's truck cab guide, a seller of deadening material.
  • Engine and heat. Low-frequency vibration passes through the firewall and transmission tunnel. Diesel World names the floor and tunnel as the main route for road noise and engine heat.
  • Wind. The upright shape of a truck creates turbulence around mirrors, pillars, and door seals. Dynamat describes wind as the loudest source once low-frequency road noise is controlled.
  • Ringing panels. Large, thin panels in the doors, roof, floor, and rear wall act like drum skins. Diesel World makes the same comparison.
  • Loose metal in the sleeper. Metal-on-metal contact in the sleeper vibrates as you drive, so covering those areas helps, according to 4 State Trucks.

What to treat first in a sleeper cab

Fix mechanical problems before adding material. Dynamat notes that deadening does not replace repairs such as worn door seals, failing engine mounts, or damaged wheel bearings.

The sources do not agree on the full order. The floor, tunnel, and firewall come first in both Diesel World and 4 State Trucks, so the list below starts there.

  1. Floor and transmission tunnel. Diesel World calls these the largest panels and the main route for road noise and engine heat.
  2. Firewall. Treating it cuts underhood noise and heat closer to the source, according to Diesel World. 4 State Trucks also starts with the firewall and cab floor.
  3. Sleeper floor and under-bunk area. 4 State Trucks ranks this third, right after the cab floor.
  4. Doors. Diesel World says treated doors improve audio clarity and reduce tire roar. Dynamat ranks doors first.
  5. Roof and rear sleeper wall. Diesel World ties the roof to wind and hollow overhead resonance. Dynamat calls the rear cab wall an often-missed path in sleepers.

Materials for trucks

Match the material to the problem. Ringing panels need damping, airborne noise needs foam or a barrier, and heat needs reflective insulation.

  • Damping mat. Bonds to bare metal and reduces how much a panel rings. Use it on the floor, doors, and firewall.
  • Closed-cell foam. Absorbs higher-pitched sound that travels through the air and helps with rattle. The advantages guide explains why foam and damping do different jobs, and why added mass alone does not stop airborne noise.
  • Heat insulation. Reflects radiant heat. Engine and exhaust heat reaches the cab through the firewall and tunnel, according to Diesel World.
  • Mass barrier. Heavy vinyl or a similar layer can block airborne noise through thin metal. SoundSkins' semi-truck collection does not list a barrier product, so plan on damping and foam from its range.
Semi Truck Sound Deadening for Sleeper Cabs

Coverage and kits by cab type

Plan coverage at 25% to 60% of the flat metal, as the coverage guide explains, and measure each zone first. Listed square footage is the material in each kit, not the metal area of the cab.

Cab type

Zones to treat

Kit to start with

Listed size

Price (USD)

Day cab

Cab floor, firewall, doors, roof

Pro Plus Workshop Kit

64.5 sq ft, one roll

$494.00

Sleeper cab

Sleeper floor and under-bunk, rear wall, roof, doors

Classic Black Sound Deadening Roll

38.75 sq ft

$199.00

Peterbilt 389

Cab floor, corners, and doors, with no sleeper or roof

Pro Peterbilt 389 Floor & Sound System Kit

54.9 sq ft, 13 pieces

$495.00

Engine side, any truck

Hood and firewall outside the cab

Heat Shield kit

53.82 sq ft

$285.00

  • The Peterbilt title says 2006 and newer, but its alt text says 2006 to 2023. Check your model year before ordering.
  • The Heat Shield listing says it is designed for use outside the cabin, so use it on the engine side unless SoundSkins confirms cab use.
  • Neither the Pro Plus nor the Classic roll listing states truck fit, so cut them to the zones you measured.
  • The semi-truck collection lists no Freightliner, Kenworth, or Volvo kit, and no sleeper-specific kit.

Install approach for a sleeper cab

Plan the access work first. Lining a sleeper floor and ceiling means removing the flooring, seats, panels, and coverings, which 4 State Trucks calls the time-consuming part.

  1. Fix leaks and loose parts first. Before adding material, inspect for loose clamps and brackets, a damaged shifter boot, and worn mounts and seals.
  2. Strip to bare metal. Remove the flooring, seats, panels, and coverings, then vacuum out loose debris.
  3. Clean with denatured alcohol. Other solvents can leave a film, according to the single-cab truck guide.
  4. Roll each piece with a wood or rubber roller. The same guide warns that metal rollers can tear the material. Press out air pockets too, since any pocket with poor adhesion cuts the benefit.
  5. Check for wiring and airbag parts before pulling dash or steering trim. Disconnect the battery before you work near them.
  6. Protect door mechanisms. Follow the door card removal guide before you pull a door card, and keep material away from the window mechanism and other moving parts.

Mistakes that waste money

These mistakes waste material or cut the benefit:

  • Air pockets. The single-cab truck guide says any air pocket with poor adhesion means you will not get the full benefit.
  • Relying on carpet alone. 4 State Trucks says carpet is not a complete fix on its own, and carpet sets must match the truck's configuration.
  • Buying the wrong kit. The Peterbilt kit fits only the 389, so check the model year before ordering any kit.
  • Overbuying. The single-cab guide notes that excess material can add weight without a clear benefit.
  • Skipping the wheel-well panels. 4 State Trucks lists the interior panels next to the wheel wells as their own treatment zone, so check them after the floor and doors.

FAQ

Will sound deadening stop engine noise? Not fully. Diesel World notes that diesel combustion produces strong low-frequency energy that is hard to isolate, so expect a reduction rather than silence.

Does it help with heat too? Yes. Floor, firewall, and tunnel treatments address heat as well as noise, and reflective insulation adds to that effect.

How much coverage does a sleeper need? Sources disagree. The SoundSkins coverage guide sets 25% as a minimum and 60% for a clear result. Second Skin's truck guide calls for 100% cabin coverage.

Is it a DIY job? It can be, if you can take the cab apart safely. The work is mostly access and cleaning rather than the material itself.

Which SoundSkins kit fits a Freightliner? None is listed. The semi-truck collection has no Freightliner kit, so measure the cab and cut a universal roll to fit, or confirm fit with SoundSkins before you order.

Conclusion

Fix the leaks first, then treat the cab floor, firewall and tunnel, sleeper floor, doors, and roof in that order. Buy only the kits that fit your truck, and measure each zone before you order.

For a truck-specific square footage example, read the single-cab truck guide. For how damping and foam differ, read the advantages guide.

Productos
Step 1

To install the material you need be working on the metal surface of the car, remove upholstery. If you have never done this, we suggest searching it up on YouTube. Once the upholstery is removed, make sure there is no debris, waxy oils or rust by cleaning the surface with denatured alcohol.

Step 2

Once surface is clean and ready to go, cut the sound deadening material to the right size so it fits desired area. For small surfaces, we recommend that you measure the dimensions and then cut to fit.

Step 3

With the surface area clean and pieces cut to desired dimensions, peel off the paper and apply material to surface area starting from the top to bottom using the car door holes to help with alignment. We recommend using a hand roller to ensure that there are no air pockets and ensure the adhesiveness.

Sound Deadener Install On Jeep

SOUNDSKINS GLOBAL

Related Products

Shop now

Sound Deadener Install FAQ: Tips & Tricks

What tools will I need to for a sound deadening project?  
  • Rag & Denatured Alcohol: Apply the alcohol to the rag and use to clean the metal surface areas you will be applying the material to.
  • Gloves: Our product is pretty safe to install without gloves but if you have never installed a sound deadener mat, we recommend using gloves.
  • Hand roller: We highly recommend using a small roller to reach the tighter surface areas of your vehicle. You can find these on Amazon or most online retail shops. There are wooden, rubber and metal rollers, we recommend wooden or rubber, try and stay away from metal as they can tear the material.
  • Utility Knife: The utility blade is to cut the material. Make sure to cut the material on top of a pice of cardboard so that your blade stays sharper longer, if it's a big job, have some extra blades around.
How do you apply sound deadener material? 

We sell our roll on sound deadener product in 2 different formats: custom cut to fit pro kits and an easy to work with rolled up large sheet. If you can measure, cut, peel and stick you can install sound deadener! You can use your hand to apply pressure when positioning the material and then use a roller to make sure it sticks down to metal surface.

After you cut the material and are ready to stick it on, some customers find it easier to peel off a small portion of the release liner and then apply it to metal surface, and then work their way across the sheet, peeling off a small section at a time.

Make sure to always remove the air bubbles with the roller. The second most important thing when it comes to quality of sound deadener is the quality of adhesion to the surface area. You want the material to be stuck down properly to ensure it stays in place.

Where do you apply the sound deadening material?  

The great thing about our sound deadening material is that it can be applied to all types of metal surfaces. All SoundSkins sheets use extremely strong adhesive and they can even be mounted on fiberglass, plastic and even wooden surfaces, but it's not very common to apply to these surfaces since they don't vibrate as much. By covering all metal surfaces such as your doors, roof, trunk and floor you can make a significant difference to unwanted road noise.

Your top priority when applying a car sound deadener is to cover the doors, floor and trunk. If you have extra material then proceed to other metal surfaces you wish to cover for extra sound insulation.

How much surface area should I cover?  

To properly deaden the metal surfaces, we recommend to at least do 25% coverage with our SoundSkins material, this will make a difference in unwanted road noise, but to have a huge impact we recommend covering up 60% of metal surfaces. If you want to get the most used from your sheet, one effective strategy is the CHECKER BOARD APPROACH, using this technique you cut the SoundSkins sheet into small pieces and apply them to the metal surface in a checkered pattern.

It is very common for our customers to do close to 100& coverage to any metal surface because not only are they looking to reduce road noise, they also want to insulate their car from heat or they like the way the material looks on the car's bare metal surface.

How do I make sure the sound deadener sticks well?

SoundSkins products are made with a very strong adhesive and create a extremely strong bond with the metal, it's really hard to NOT make it stick. To ensure the best possible bond, we highly recommend cleaning the metal surface before applying our material and then using a hand roller to firmly attach the SoundSkins deadening mats.

Great adhesion with no air bubbles is the absolute key if you want to get the best performance. Remember that any air pocket with poor adhesion means you will not get the full benefit of the deadener.

How to install car sound deadener: Recap
  1. Remove upholstery and carpet from your vehicle. Proceed to vacuum to get rid of debris and dirt. Clean all greasy spots with denatured alcohol, other solvents or degreasers will leave behind a film that prevents a solid contact surface. Allow metal surface to try.
  2. Cut the SoundSkins sheet to desired size and cut using a sharp utility knife. Use gloves to avoid any cuts.
  3. Peel off the wax paper from the back of material and apply to surface, this can be done by small sections at a time. Use roller to create a strong bond between material and metal surface and to get rid of any air bubbles.

If you have any questions, make to reach out to use and we'll be happy to help.

SOUNDSKINS GLOBAL